failed to read packet header from the GIMX adapter

Need help? Ask here and someone will help
Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 11:58 am

hi
i build my GIMX adaptor with these :
https://translate.google.com/translate? ... micro.html

https://translate.google.com/translate? ... l2303.html.

i load EMUPS4->atmega32u4.hex with arduino builder 1.0.13 and i get a screen.
then i try to use the Adapter i connect Micro Usb to PS4 and the Usb to the Pc then Start
i get "failed to read packet header from the GIMX adapter"

first
Image
then
Image

User avatar
Matlo
Posts: 5284
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: failed to read packet header from the GIMX adapter

Post by Matlo » Thu Jan 31, 2019 12:13 pm

Try using gimx-loader instead: https://backup.gimx.fr/wiki/index.php?t ... g_firmware

Make sure the wiring is correct. If it's not gimx-loader will fail to load the firmware.
GIMX creator Donate Shop

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 12:33 pm

Matlo wrote:
Thu Jan 31, 2019 12:13 pm
Try using gimx-loader instead: https://backup.gimx.fr/wiki/index.php?t ... g_firmware

Make sure the wiring is correct. If it's not gimx-loader will fail to load the firmware.
Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

User avatar
Matlo
Posts: 5284
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: failed to read packet header from the GIMX adapter

Post by Matlo » Thu Jan 31, 2019 12:48 pm

Post a clear picture showing the wiring.
GIMX creator Donate Shop

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 12:58 pm

Matlo wrote:
Thu Jan 31, 2019 12:48 pm
Post a clear picture showing the wiring.
orange wire = blue wire
Image

Image
Image

adaptor is off on these photo:
Image
Image
Image

some times RED led on "CP2102 USB To TTL Module" is off just some times.

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 1:02 pm

is there any way to flash or reboot arduino pro micro ?
i try short connect with GRD and RST

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 1:03 pm

arduino pro micro is not in arduino builder!!

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Thu Jan 31, 2019 1:08 pm

for first time i load the firmware there was A Com 4 but after that it's gone !!!
Image

User avatar
Matlo
Posts: 5284
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: failed to read packet header from the GIMX adapter

Post by Matlo » Thu Jan 31, 2019 1:42 pm

The COM port not being here anymore suggest that firmware was correctly loaded.

However the wiring/soldering looks bad.
Remove the electrical tape and solder the green/yellow/blue wires directly on the pro micro board.
Also I can't be sure from the pictures but I think the tin quality is bad.
GIMX creator Donate Shop

Davros
Posts: 19
Joined: Sat Jan 26, 2019 11:01 am

Re: failed to read packet header from the GIMX adapter

Post by Davros » Mon Feb 04, 2019 11:17 am

i buy a new arduino pro micro first of all
Image
i get a red led in arduino and no led in CP2303 !!!

and one of them i must select for arduino pro micro ?!

Image

Post Reply