DIY USB Adapter für Dummies

From GIMX
Jump to: navigation, search

This page is a translated version of the page DIY USB adapter for dummies and the translation is 75% complete.


Other languages:
Deutsch • ‎English • ‎français • ‎中文(中国大陆)‎

gfd-header.png

Diese Anleitung fokussiert sich nur auf das wesentliche und wird einfach gehalten. Für weitere Details DIY_USB_adapter.


Willkommen zur Schritt-für-Schritt Anleitung um einen GIMX DIY USB Adapter zu bauen, ohne zu löten!
Alles was man benötigt und wissen muss um um den Adapter zu bauen und bereit zu machen steht hier, wenn man es gut durch liest!
Es empfiehlt sich, die Anleitung zuerst einmal durch zu lesen, bevor man damit beginnt.

Die benötigten Teile besorgen

Der Converter sollte mit einigen Kabeln geliefert werden und folgendermassen aussehen:

gfd-cp2102.jpg

Es wird zwingend ein Teensy-Board mit Pins benötigt, damit nichts gelötet werden muss.
Es kann ein Teensy 2.0 oder ein Teensy ++ 2.0 verwendet werden.
Die anderen Teensy Boards (3.x, LC, etc..) sind NICHT kompatibel.

Falls noch nicht vorhanden, werden noch USB-Kabel wie diese benötigt:

Optional:

Ich werde für diese Anleitung eine Zündholzschachtel verwenden.
  • Isolierband
Um die Teile zu isolieren resp. zu befestigen.
  • Gummibänder
Um alles zusammen zu halten - einfach wieder zu entfernen, falls etwas nicht stimmt.

Und Hoffentlich ist eine kleine Grundausstattung an Werkzeugen vorhanden. z.B. Messer oder Scheere.

gfd-parts.jpg

Notiz: Anstelle von einziehbaren Kabeln, geschirmte USB-Kabel verwenden.

Benötigte Software, Firmwares und Treiber herunterladen

Windows

  • EMUJOYSTICKPS3: HID joystick emulation, with 16bit stick axes, for PS3
  • EMUPS3: Sixaxis emulation, for PS3
  • EMU360: 360 pad emulation, for Xbox 360
  • EMUPS4: Hori Pad FPS Plus emulation, for PS4 (with touchpad support)
  • EMUXONE: Xbox One pad emulation, for Xbox One
  • EMUG29PS4: Logitech G29 gaming wheel emulation, for PS4, with force feedback support
  • EMUG27PS3: Logitech G27 gaming wheel emulation, for PS3, with force feedback support
  • EMUGTFPS2: Logitech GT Force emulation, for PS2, with force feedback support
  • EMUDFPS2: Logitech Driving Force emulation, for PS2, with force feedback support
  • EMUDFPPS2: Logitech Driving Force Pro emulation, for PS2, with force feedback support
  • EMUG27PC: Logitech G27 gaming wheel emulation, for PC, force feedback support

Für die einfache Handhabung alles auf den Desktop speichern resp. entpacken.

--todo: update screenshot (CP210x drivers are included in the GIMX setup) gfd-files.png

Ubuntu

  • EMUJOYSTICKPS3: HID joystick emulation, with 16bit stick axes, for PS3
  • EMUPS3: Sixaxis emulation, for PS3
  • EMU360: 360 pad emulation, for Xbox 360
  • EMUPS4: Hori Pad FPS Plus emulation, for PS4 (with touchpad support)
  • EMUXONE: Xbox One pad emulation, for Xbox One
  • EMUG29PS4: Logitech G29 gaming wheel emulation, for PS4, with force feedback support
  • EMUG27PS3: Logitech G27 gaming wheel emulation, for PS3, with force feedback support
  • EMUGTFPS2: Logitech GT Force emulation, for PS2, with force feedback support
  • EMUDFPS2: Logitech Driving Force emulation, for PS2, with force feedback support
  • EMUDFPPS2: Logitech Driving Force Pro emulation, for PS2, with force feedback support
  • EMUG27PC: Logitech G27 gaming wheel emulation, for PC, force feedback support

Adapter zusammenbauen

Bevor begonnen wird, überprüfen ob der Serielle-Konverter genau der gleiche wie in dieser Anleitung ist.
Der Adapter in dieser Anleitung ist falsch angeschrieben: RXD und TXD sind vertauscht.
Falls es nicht exakt der selbe Adapter ist, müssen möglicherweise die Pins anders verbunden werden:

Teensy USB zu UART Board
GND GND
D2 TX / TXO / TXD
D3 RX / RXI / RXD

Falls der Adapter in einem kleinen Gehäuse kontakt mit anderen Bauteilen herstellen könnte, ist es empfehlenswert den Seriellen-Konverte mit Isolierband zu isolieren damit keine Schäden an den Bauteilen auftreten.

gfd-insulate.jpg

Nun die Kabel wie auf dem Bild zu sehen ist verbinden. (Position des Teensy-Boards beachten ! Die Pins sollten nach links zeigen, mit der USB Schnittstelle weg von einem.)

gfd-cablesgohere.jpg

Die nächsten zwei Schritte sind nur benötigt, wenn der Adapter in einen sehr kleinen Behälter verbaut wird und deshalb sehr klein gehalten werden muss.

1. Die Pins an welche die Jumper-Kabel befestigt sind langsam und vorsichtig nach innen biegen damit sie nicht abbrechen. Die Kabel zwischen den Pins hindurchführen.

gfd-bend-1.jpg

2. To save some extra space, I usually wrap the cables around the Teensy. There's no special way of doing this, so you just need to figure out what works best for your build.

Remember not to cover up the button on the Teensy as we need to press it later on. (Also, this is where the rubber band will come in handy!)

gfd-bundle.jpg

If you want, you can also place the serial converter so that the pins and jumper cables go in between the rows of pins on the Teensy. It's a very snug fit though so you should use some electrical tape to insulate the pins on the serial converter because they will touch the Teensy ones if you don't.

gfd-insulate2.jpg

Cut some holes in your project box of choice to match the Mini USB plug on one side and regular USB plug on the other side. Do some tests and make sure everything aligns up before securing everything in place. In the picture below I've bundled everything up using the rubber band and secured it to the box with some electrical tape (double sided tape or hot glue works wonders too if you have it)

gfd-matchdapter.jpg

Voilà! Der Adapter ist fertig gebaut.

Firmware auf den Adapter laden

Den Adapter mit dem USB-Mini-B-Kabel am PC anschliessen, das Teensy Board sollte starten oder zu Blinken beginnen.

gfd-loadfirmware.png

Nun den Teensy Loader starten (teensy.exe auf dem Desktop) und folgende Schritte durchführen:

Press the button on the Teensy and the LED should turn off. In Teensy Loader, open atmega32u4.hex from the firmwares folder on your desktop. Click the Program button and you should get the message "Download Complete" Now click the Reboot button and your GIMX USB adapter is ready for use!

Falls der Teensy Loader kein Gerät erkennt, sollte ein anderes USB-Kabel resp. ein anderer USB-Port genommen werden.

gfd-connect.jpg

NOTE! You can now unplug the USB Mini-B cable from your computer. The USB Mini-B cable will only be connected to your computer when upgrading the firmware from now on. When in use, the USB Mini-B cable is connected to your console.

GIMX Software installieren

This step is pretty straight forward. Simply run setup-X.YZ.exe from your desktop and follow the installation steps, preferably with the default installation location.

gfd-setupgimx2.jpg

Wenn die Installation abgeschlossen ist, sollten drei GIMX Icons auf dem Desktop erzeugt werden.

--todo: update screenshot (gimx-serial was renamed to gimx-launcher) gfd-icons.png

Konfigurationsgrundlagen

GIMX comes pre-loaded with a few configurations, but let's take a quick look on how you can make your own configurations using the GIMX FPS Config Tool (As you can tell by the name, this is mainly meant for setting up a basic FPS configuration.)

Youtube video

You can also check out the Configuration Requests and Index thread for other configurations available for download, or post requests that we or the community might be able to fulfill.

NOTE! To open the configuration directory, click on File>Open config directory in gimx-config, gimx-fpsconfig, or gimx-launcher.

Bereit zum Start!

Fertig. Nun ist der GIMX USB-Adaper bereit für die Verwendung!

  • Normale USB-Siete mit dem PC verbinden

gfd-contopc.jpg

  • Connect the USB Mini-B side to your console, run gimx-launcher and make sure the adapter is recognized on a COM port.
(If the Device box is blank, refer to the Support section and report the problem if a solution isn't found)

gfd-comport.jpg

  • Read the Quick Start page to learn how to download a pre-made configuration, and how to install the libusbk driver (needed for consoles that require authentication).
  • Select the config you made/downloaded from the drop down menu, click the Start button and a couple of windows should pop up to start capturing your mouse and keyboard input!

If there is a "No controller detected." error message when you start GIMX, double check you wiring, and try to invert TX and RX in case it's still not working.

gfd-selconfig.png

Now if you're in the menus of your console and press the WASD or arrow keys on your keyboard, you should be able to navigate through the menus, meaning you've succeeded! If not, or if something went wrong elsewhere, go back and make sure you followed every step to the letter and try again, then let us know if nothing you try works.

Viel Spass!