Difference between revisions of "DIY USB adapter"
| Line 27: | Line 27: | ||
* USB development board: | * USB development board: | ||
** [http://www.pjrc.com/store/teensy.html Teensy board (atmega32u4, 16$ excl. shipping costs)] (to build a solderless adapter, take a board with header pins) | ** [http://www.pjrc.com/store/teensy.html Teensy board (atmega32u4, 16$ excl. shipping costs)] (to build a solderless adapter, take a board with header pins) | ||
| − | ** [http://arduino.cc/en/Main/ArduinoBoardLeonardo Arduino Leonardo] - [http://arduino.cc/en/Main/Buy distributors] - (cheap clones | + | ** [http://arduino.cc/en/Main/ArduinoBoardLeonardo Arduino Leonardo] - [http://arduino.cc/en/Main/Buy distributors] - (cheap Chinese clones can be found on ebay for 19$ incl. shipping costs) |
** Boards used for the psgroove hack (check the on-board chip). | ** Boards used for the psgroove hack (check the on-board chip). | ||
Revision as of 23:17, 18 September 2012
This page explains how to build a pc to ps3/360 usb adapter.
A much easier but less complete tutorial is also available: DIY USB Adapter for dummies.
A German translation of a previous version is also available on the forum: old German translation.
Warning: you are responsible for the hardware you buy, and anything right or wrong you do with this.
Required hardware parts
- a USB to serial TTL converter that can work at 500kbps - chip examples: FT232R, CP2102
- a USB development board with a chip among the following: at90usb82, at90usb162, at90usb646, at90usb647, at90usb1286, at90usb1287, atmega16u2, atmega32u2, atmega16u4, atmega32u4
Examples:
- USB to serial TTL converter:
- CP2102 converters on ebay (as low as 4$)
- FT232R converters on ebay (as low as 15$)
- CP2102 converter at sparkfun (22$ excl. shipping costs)
- FT232R converter at sparkfun (15$ excl. shipping costs)
- Some devices like the arduino have an on-board usb to serial chip
- A second usb development board can also be programmed as a usb to serial converter.
- USB development board:
- Teensy board (atmega32u4, 16$ excl. shipping costs) (to build a solderless adapter, take a board with header pins)
- Arduino Leonardo - distributors - (cheap Chinese clones can be found on ebay for 19$ incl. shipping costs)
- Boards used for the psgroove hack (check the on-board chip).
Tested and working:
- Arduino duemilanove (on-board FT232RL) + Bumble-b (discontinued, at90usb162)
- Arduino duemilanove (on-board FT232RL) + Teensy++ (at90usb1286)
- CP2102 board (from ebay) + Teensy 2.0 (atmega32u4)
- CP2102 board (from ebay) + Teensy++ (at90usb1286)
Recommended: CP2102 converter from ebay (very low price, but sometimes low delivery) and the Teensy board (low price, good quality, and quick delivery).
Firmware loading
Firmwares:
There are several tools that can be used to load the hex file:
- Teensy loader (only compatible with genuine teensy boards)
- Flip utility from Atmel (not compatible with genuine teensy boards)
- dfu-programmer command-line tool (not compatible with genuine teensy boards)
dfu-programmer example:
sudo dfu-programmer at90usb162 erase ; sudo dfu-programmer at90usb162 flash at90usb162.hex
Wiring
The only thing you have to do is to connect the following pins:
- GND <--> GND
- RX <--> TX
- TX <--> RX
The example below shows how to connect a CP2102 converter (left) to a Teensy board (right):
It's possible to solder wires or to use jumper wires (these are generally provided with USB to serial TTL boards) in case your AVR USB board has header pins:
Warning: Rx and Tx may be inverted on the usb to serial TTL board.
The CP2102 converter in the above example has inverted Rx and Tx.
If you use the arduino on-board USB to serial converter, Rx and Tx are inverted.
Examples:
- Bumble-b and FT232RL wired on a breadboard:
- Teensy++ and CP2102 wired on a breadboard:
- Teensy and CP2102 soldered:
Connection
If you are using windows and a CP2102 usb to ttl board, install the CP2102 windows drivers first (mandatory).
Connect the USB to serial converter to your PC, and connect the usb dev board to your ps3. Turn the PS3 on (the ps button is not working yet). The ps3 should detect a joystick (turn a sixaxis on, it should be detected as controller #2).
If it's not already done, install GIMX.
Start gimx-serial:
In Ubuntu/Linux, the USB to serial TTL converter should be detected as "ttyUSBX" (with 'X' a number).
In Windows, it should be detected as "COMX" (with 'X' a number). Check the device manager to select the right one.
