PS4 - Dirt - G29 - No Tension

[pocopoco]

Log will be under /root/.gimx/log directory
To enable log use -l logFileName.log parameter

Pay attention that the log file will be overwritten if gimx restarts

[zblad]

Alright I will try get the log file over lunch. The only issue is I don't think its really going to show anything because everything works fine its just missing the tension. My steering wheel calibrates the instant I power the pi on and it only does it once. Once the pi has booted I have a button I press that starts gimx my steering wheel does not recalibrate when I press this button. I press the button gimx starts and everything works. Just to restate my wheel only calibrate once and that is right when the pi gets power.

[pocopoco]

This is the same for me. It is normal, the wheel start calibration when you connect the usb

[zblad]

Are you using the Logitech force gt steering wheel and does your wheel have tension right away?

[zblad]

global option -l with value `log.txt'
GIMX 5.8 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.4.15-v7+ #897 SMP Tue Jul 12 18:42:55 BST 2016 unknown
Bus 001 Device 006: ID 046d:c29a Logitech, Inc.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
cannot get USB device tree
native mode is already enabled for HID device 01:01:02 (PID=c29a)
Detected USB adapter: G29 PS4.
No controller was found on USB buses.
adapter_detect failed


THis was the log file which is weird because my steering wheel worked???

[pocopoco]

No controller was found on USB buses.
adapter_detect failed

No good.

Connect original console controller to you rpi and usb-serial converter

[zblad]

global option -l with value `log2.txt'
GIMX 5.8 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.4.15-v7+ #897 SMP Tue Jul 12 18:42:55 BST 2016 unknown
Bus 001 Device 006: ID 046d:c29a Logitech, Inc.
Bus 001 Device 005: ID 054c:05c4 Sony Corp.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Vendor Specific Class, Driver=smsc95xx, 480M
|__ Port 2: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 12M
|__ Port 4: Dev 6, If 0, Class=Human Interface Device, Driver=usbhid, 12M
native mode is already enabled for HID device 01:01:04 (PID=c29a)
Detected USB adapter: G29 PS4.
using default refresh period: 5.00ms
1471629176.821093 timer fired 7 times...

[zblad]

Ignore that first log file I didnt realize it didnt update...

[zblad]

so i did downgraded my firmware via a differnt post. ANd that corrected my issues. Thank You so much!!!!

sudo rpi-update 771a503cfc2a1130e2df2a4ddfc45ffa0f592b3f

[Matlo]

Thanks for the feedback. I added a note on the wiki page.