[config] Battlefield 3

[HIGH5]

I will be updating the post with an revisited config when I get the game. It'll hopefully arrive tomorrow.

^Cool

[blackhoot]

It is my first configuration with the marvelous GIMX. Thanks Matlo.

For the moment, I just played in first 2 levels solo with the following regulations:

Conf 1:
x 31 / 18 / 0.40 / Circle
y 31 / 22.5 / 0.40 / Circle

Conf 2:
x 31 / 20 / 0.40 / Circle
y 31 / 30 / 0.40 / Circle

And I have a G5 in 2000 dpi.

[McKack]

Thanks for sharing the values. I was meaning to get it done today but I got held up so I'll get to making my own config first thing tomorrow and share for anyone to use or tinker with.

[kachijs]

Thanks for sharing the values. I was meaning to get it done today but I got held up so I'll get to making my own config first thing tomorrow and share for anyone to use or tinker with.

ok. i have logitech mx 1000 is it ok to use your mouse config or i need to calibrate it myself ? i dont really know how to do it properly. Its harder when linux and ps3 is connected to LCD TV with no additional external display

[drfrink24]

I have my deadzone bumped up to over 40.. still jerky aim.. Funny though, when driving a tank or manning any turret/launcher, the movement is perfect. I'll play around with these settings tonite.

[McKack]

Yup I'm still messing around with it. Lots of different vehicles and stuff to cover.
But in the end, the aim is coded differently than CoD so it'll always be a little laggy and sluggish, but luckily not as bad as Bad Company.

ok. i have logitech mx 1000 is it ok to use your mouse config or i need to calibrate it myself :( ? i dont really know how to do it properly. Its harder when linux and ps3 is connected to LCD TV with no additional external display :D

The current config only supports soldier layout (It's the Beta-config) But if you do decide to give it a go, you just use the DPI replacement function in the menus of the sixemuconf to set it to match your DPI.
800DPI is very low though, below the minimum recommended (around 1600-2000)

[Dr-Ripper]

After trying lot's of configurations, i can't found a good one...
So cannot post a usefull config for BF3
but the best results (for me) are in a range of 40 for dead zone and 2500 DPI (G700 mouse)
I set mouse to 5700 dpi when i board a tank or heli.

[kachijs]

ok. i have logitech mx 1000 is it ok to use your mouse config or i need to calibrate it myself ? i dont really know how to do it properly. Its harder when linux and ps3 is connected to LCD TV with no additional external display

The current config only supports soldier layout (It's the Beta-config) But if you do decide to give it a go, you just use the DPI replacement function in the menus of the sixemuconf to set it to match your DPI.
800DPI is very low though, below the minimum recommended (around 1600-2000)

Hmm. http://www.techpowerup.com/reviews/Logitech/MX1000/ this site says that i have 800 DPI too.

[Matlo]

but the best results (for me) are in a range of 40 for dead zone and 2500 DPI (G700 mouse)
I set mouse to 5700 dpi when i board a tank or heli.

You should decrease the sensitivity = multipliers and let your mouse DPI set to 5700.

[Dr-Ripper]

but the best results (for me) are in a range of 40 for dead zone and 2500 DPI (G700 mouse)
I set mouse to 5700 dpi when i board a tank or heli.

You should decrease the sensitivity = multipliers and let your mouse DPI set to 5700.

ok thanks,

until friday im busy, but i will try to test a configuration using your sugestions