Page 1 of 1

GIMX recognizes G920 as "Xinput Controller"

Posted: Wed May 18, 2022 12:39 am
by pelicano
Hello.

Suddenly, after a week or something of not using it, both gimx-launcher and gimx-config started displaying the message "joystick not found: Logitech G HUB G920 Driving Force Racing Wheel USB (0)". When I go to gimx-config, all my inputs are registered as "joystick Xinputcontroller 0". This only happens on Windows, as I just tested on my Ubuntu drive and it worked flawlessly. Screenshots below:

Image
Image
Image

My G920 is working normally, both through my PC (on Assetto Corsa, e.g.) and on PS4 via GIMX on Ubuntu 21.10.

Checked (doubt it is any of this, as it worked on Linux without changes):
- GIMX is connected to PC and to PS4;
- Wheel and pedals connected to PC;
- Dualshock 4 turned off and then connected to PC;

Already tried:
- Restarted computer;
- Do a configuration with "Xinput" instead of G920
- Reinstalled G HUB
- Uninstalled G HUB and installed Logitech Gaming Software
- Reinstalled GIMX

Appreciate any help. Thanks in advance.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Thu May 19, 2022 1:06 am
by pelicano
Anyone?

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Thu May 19, 2022 2:56 am
by kaiba_seto2004
I think problem is windows driver. You can try with another windows pc.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Thu May 19, 2022 11:51 am
by pelicano
kaiba_seto2004 wrote: Thu May 19, 2022 2:56 am I think problem is windows driver. You can try with another windows pc.
I also reinstalled my G920 drivers (removing and deleting drivers from device manager) and the problem has not been solved.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Fri May 20, 2022 9:07 am
by GoDlike
Try to reinstall LGS

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Fri May 20, 2022 1:08 pm
by pelicano
GoDlike wrote: Fri May 20, 2022 9:07 am Try to reinstall LGS
Also tried that, sadly. Reinstalled, didn't work and then uninstalled. Now running G HUB again. Yesterday I uninstalled all drivers I could find that had relation to the wheel and installed again, but with no luck :cry: .

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Fri May 20, 2022 5:59 pm
by GoDlike
It's weird. GIMX tries to read the input device and windows passes him XINPUT device like a controller. Not a wheel that uses direct input.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Fri May 20, 2022 6:35 pm
by pelicano
GoDlike wrote: Fri May 20, 2022 5:59 pm It's weird. GIMX tries to read the input device and windows passes him XINPUT device like a controller. Not a wheel that uses direct input.
Yeah, it's getting on my mind. Tried everything that I could. Next step is to debug GIMX code, but I would like to avoid that lmao.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Sun May 22, 2022 2:41 am
by AeroX
If you have Steam installed might be worth checking Steam Controller Settings as it can change how various "controllers" are detected by Windows in an attempt to increase compatibility with games.

I had a USB Gearstick being detected as a Xbox Controller which was causing me issues in racing games. I had to go to Settings > Controller > General Controller Settings > untick "Xbox Configuration Support" in my case.

Re: GIMX recognizes G920 as "Xinput Controller"

Posted: Sun May 22, 2022 11:46 pm
by pelicano
AeroX wrote: Sun May 22, 2022 2:41 am If you have Steam installed might be worth checking Steam Controller Settings as it can change how various "controllers" are detected by Windows in an attempt to increase compatibility with games.

I had a USB Gearstick being detected as a Xbox Controller which was causing me issues in racing games. I had to go to Settings > Controller > General Controller Settings > untick "Xbox Configuration Support" in my case.
Yeah I checked that also.. sadly it was not checked.

Image