I have the exact same problem. did the update of the RPi and booted only into console to save resources on the Pi, but nothing after 1-3 minutes it disconnects and the power status led on the G25 starts to blink. Really don't know what's wrong with it.
How can I get a log to post here on the forum out of the gimx software, because in the console it just states this "LIBUSB_TIMEOUT..." Error message. but as described above this is not that bad on the Pi.
Best regards, Max.
Raspberry Pi3 + DIY USB + G27=Perfect only for a few minutes
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
You can get the log launching GIMX from GUI and selecting Log as output. Then you can get the file generated at /home/pi/gimx-launcher/log or /home/pi/.gimx/log, I don't remember exactly the location.
I didn't try anything else, If you get it, please cooment the solution in this post.
Regards
I didn't try anything else, If you get it, please cooment the solution in this post.
Regards
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
Add "--log file.txt" at the end of the command line.
The generated file is in the /home/pi/.gimx/log directory.
The generated file is in the /home/pi/.gimx/log directory.
GIMX creator
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
Code: Select all
0 1461764489.520707, wheel (-4062), gas (44294)
0 1461764489.525742, wheel (-4034), gas (44824)
0 1461764489.530700, wheel (-4018), gas (44824)
libusb_transfer failed with status LIBUSB_TRANSFER_TIMED_OUT (endpoint=0x01) //this is when the wheel fails and no inputs are on the PS4
libusb_transfer failed with status LIBUSB_TRANSFER_TIMED_OUT (endpoint=0x01)
libusb_transfer failed with status LIBUSB_TRANSFER_TIMED_OUT (endpoint=0x01)
libusb_transfer failed with status LIBUSB_TRANSFER_ERROR (endpoint=0x84) //then i disconnect the DS4 to finally crash gimx, otherwise it will not crash
best regards
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
Exactly the same behavior that i described
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
I also did all the updates and even a reinstall of raspbian with the "tested" version from last october, nope that kernel didn't even let me start the program, now i'm on the version matlo posted with the "rpi-update" command still nothing, even now there is a little bit better force feedback than before, idk why but the center is a bit less dead and feels more active.Exactly the same behavior that i described
hope we can get a solution here i don't want to use a laptop beside my racing rig
@matlo i donated to your paypal yesterday so you can keep up the good work!
best regards
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
@dermax93
Thanks for the donation. Could you please post a full log file please?
Thanks for the donation. Could you please post a full log file please?
GIMX creator
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
In my first post you have a log.
http://pastebin.com/rmPwwg23
Sometimes there are much more LIBUSB_TRANSFER_TIMED_OUT errors. only when I unplug USB wheel I get the LIBUSB_TRANSFER_ERROR message. The same situation described by dermax93 I guess.
http://pastebin.com/rmPwwg23
Sometimes there are much more LIBUSB_TRANSFER_TIMED_OUT errors. only when I unplug USB wheel I get the LIBUSB_TRANSFER_ERROR message. The same situation described by dermax93 I guess.
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
I did upload a whole log to pastebin you can find it here Pastebin Log File.
im on this version of Jessie:
I did no modifications at all to the software to improve performance whatsoever...
kind regards.
im on this version of Jessie:
Code: Select all
i@raspberrypi ~ $ uname -a
Linux raspberrypi 4.1.21-v7+ #873 SMP Mon Apr 11 18:22:10 BST 2016 armv7l GNU/Linux
kind regards.
Re: Rasberry Pi3 + DIY USB + G27=Perfect only for a few minu
Once you get the LIBUSB_TRANSFER_TIMED_OUT do you desconnect the Wheel?? Then LIBUSB_TRANSFER_ERROR appears??