Hi everyone. Thank you Matlo for this great project. I am trying to use a DIY adapter on Xbox360 console with Dualshock4 controller.
I have modified gimxcontroller/firmware code to authenticate with a 3rd party Afterglow controller (used a tutorial from this forum).
When I start Gimx with Dualshock4.xml file, DS4 is working, but all the mappings are incorrect
Edit: Fixed it by creating a new config file with the Gimx configurator.
xbox360 with ds4 incorrect mapping issue
-
- Posts: 5
- Joined: Wed Jan 13, 2021 11:30 am
xbox360 with ds4 incorrect mapping issue
Last edited by wahef58696 on Fri Jan 22, 2021 11:00 pm, edited 11 times in total.
- LoneWolf81
- Posts: 235
- Joined: Sat Jun 15, 2019 11:49 am
- Location: South Africa
Re: xbox360 with ds4 incorrect mapping issue
Hi
If you open the file with the config editor is the type set to 360pad ? From the log file it looks like its still set to Dualshock 4
If you open the file with the config editor is the type set to 360pad ? From the log file it looks like its still set to Dualshock 4
Please Remember to Post your Log file in the support section , that way its easier and faster to start identifying the issue thus helping you to sort it out so you can enjoy GIMX .
-
- Posts: 5
- Joined: Wed Jan 13, 2021 11:30 am
Re: xbox360 with ds4 incorrect mapping issue
changed it to type="360pad" now, but nothing changed . RS sends guide, guide sends LS, triangle sends B etc.
what exactly does type variable do?
another note:
after launching Gimx, it starts working immediately (after the vibration) without pressing the guide button. it still
says "Press the guide button of the controller for 2 seconds". Meanwhile xbox controller's light is a complete ring
fading in and out (like the wireless controller waiting to be synced). However holding the guide button does nothing.
Is is that because I am using a 3rd party controller for authentication?
what exactly does type variable do?
another note:
after launching Gimx, it starts working immediately (after the vibration) without pressing the guide button. it still
says "Press the guide button of the controller for 2 seconds". Meanwhile xbox controller's light is a complete ring
fading in and out (like the wireless controller waiting to be synced). However holding the guide button does nothing.
Is is that because I am using a 3rd party controller for authentication?
- kaiba_seto2004
- Posts: 554
- Joined: Sat Jul 15, 2017 9:15 am
Re: xbox360 with ds4 incorrect mapping issue
On wiki, we used a genuine wired 360 controller.Bus 001 Device 003: ID 0e6f:0213 Logic3 Afterglow Gamepad for Xbox 360
I think you need to remap buttons in gimx-config.
PS4 enthusiast.
-
- Posts: 5
- Joined: Wed Jan 13, 2021 11:30 am
Re: xbox360 with ds4 incorrect mapping issue
isn't Xbox gamepad only used for authentication? DS4 is a genuine one.
- kaiba_seto2004
- Posts: 554
- Joined: Sat Jul 15, 2017 9:15 am
Re: xbox360 with ds4 incorrect mapping issue
If target console is X360, X360 wired controller is required. I'm not sure if Logic3 Afterglow Gamepad works or not.
PS4 enthusiast.
-
- Posts: 5
- Joined: Wed Jan 13, 2021 11:30 am
Re: xbox360 with ds4 incorrect mapping issue
wahef58696 wrote: ↑Wed Jan 13, 2021 11:48 am i have modified the code to authenticate with an Afterglow controller (used the tutorial from this forum).
when i start Gimx with Dualshock4.xml file, DS4 is working, but all the mappings are incorrect.
-
- Posts: 5
- Joined: Wed Jan 13, 2021 11:30 am
Re: xbox360 with ds4 incorrect mapping issue
I realized Dualshock4.xml is only a test file for PS4.
Re: xbox360 with ds4 incorrect mapping issue
Hello,
Actually it did work with earlier Linux kernels, and some recent development in the Linux kernel (probably to add touchpad and motion sensing support) broke the mappings.
I'll update the default configuration.
Thanks for letting us know about this issue
Actually it did work with earlier Linux kernels, and some recent development in the Linux kernel (probably to add touchpad and motion sensing support) broke the mappings.
I'll update the default configuration.
Thanks for letting us know about this issue
GIMX creator
Re: xbox360 with ds4 incorrect mapping issue
Sorry to revive an old thread, but does anyone know which tutorial might be the one referenced?
I saw in another thread that involved someone was trying to change the vendor and product id. https://gimx.fr/forum/viewtopic.php?t=3604I have modified gimxcontroller/firmware code to authenticate with a 3rd party Afterglow controller (used a tutorial from this forum).