Install GIMX on the RPi 3B

Need help? Ask here and someone will help
Post Reply
User avatar
kaizmoto1489
Posts: 1
Joined: Tue May 04, 2021 3:54 am

Install GIMX on the RPi 3B

Post by kaizmoto1489 »

How To Clean The Shark Nv360 Vacuum Cleaner

A vacuum cleaner is an appliance that you need to periodically clean to ensure its optimal performance. At the same time, maintain the long life of the machine. Here, we will share with you a guide on how to properly clean the Shark navigator NV360 vacuum. Please refer and follow the sequence of steps that we give!

When is it necessary to clean the vacuum cleaner?

When is it necessary to clean the vacuum cleaner? You can clean the device at any time, but make sure to follow the correct procedure and follow the manufacturer's instructions.

In addition, periodic cleaning of the vacuum cleaner is also a way to minimize equipment damage. Because after operating the machine without regular cleaning and maintenance, dirt will stick to the components, leading to the device not being able to operate stably.

Here are the common cases you need to keep in mind when using a vacuum cleaner:
  • Weaker suction leads to negligible efficiency
  • When detecting an unusual odor from the machine
  • The filter is blocked, the airflow is greatly reduced
Image

Steps to clean the Shark nv360 vacuum cleaner

We've used most versions of the Shark navigator lift away deluxe NV360 and found that the parts and basic operation are the same. Below is what you need for the best cleaning of a vacuum cleaner before reading the instructions in the article.
  • Warm water
  • Dishwashing liquid or machine cleaning solution
  • Wiper
  • Flashlight
  • Soft brush
  • Drag
  • A wooden or plastic skewer
Step 1: Disassemble the product

First of all, before cleaning, make sure that the vacuum cleaner is completely disconnected from the power source. Then you start removing the parts that need cleaning, like the dust box, filter and handle tube.

Step 2: Carefully check the parts

Thoroughly inspect every part of the machine. You may see tangled hair, pet hair, or dirt clinging to other components; try to remove them gently. Besides, you can remove all obstructions by using your hands or a wooden skewer (plastic).

Step 3: Clean the dust bag

Open the lid of the dust container and empty everything in it. Next, use warm water mixed with soap to clean the container. Use a brush or washcloth to clean and scrub away the plaque. After cleaning, please dry thoroughly!

Image

Step 4: Clean the filter

Most versions of Shark brand vacuum cleaners have a HEPA filter. The location of this filter is located under the machine, on the front of the door. Pull the door hard to get the HEPA filter out, rinse the filter with water and clean it. Note that do not assemble the filter at this time; let it dry completely to avoid mold.

Step 5: Clean the brush roll

The next step is to place the vacuum cleaner on the floor so that the brush roll of the machine can be seen. Place a bag or carton underneath to catch dirt and debris that is about to fall. If you see hair, wire, or other dirt wrapped around the brush, cut it off with scissors. And finally, clean around the brush roll.

Conclusion

We have shared the steps on how to clean the Shark Navigator Lift Away Deluxe NV360 upright vacuum to ensure it stays in good working order and lasts a long time. If you have any questions or comments, feel free to comment below, we'd love to hear from you!
Last edited by kaizmoto1489 on Mon Feb 05, 2024 8:25 am, edited 3 times in total.
User avatar
kaiba_seto2004
Posts: 553
Joined: Sat Jul 15, 2017 9:15 am

Re: Install GIMX on the RPi 3B

Post by kaiba_seto2004 »

You can follow this guide to install gimx on Rpi

Code: Select all

https://gimx.fr/wiki/index.php?title=RPi
PS4 enthusiast.
Post Reply