How do I know my ATMEGA32U4 board is working
Posted: Fri Jan 19, 2018 9:11 am
I just bought a TMEGA32U4 board which is called Risym and I read the specs I believe it would be sufficient for Gimx.
Anyway,I followed the instruction on Wiki and now I'm using the "Update firmware" in gimx-launcher , but it always pops up "failed to load firmware". As I thought it would be problems in connection or something, I downloaded the Arduino Builder and tested my board.
(I think my jumpers and pins are a little loose, cause when I'm holding the intersections with a angle, a green light on the board would turn on.)
I used "serial monitor" it didn't work, no response.
Then I tried upload sketch, no error message. But when I tried to use "Upload using programmer" the error message came out.
Arduino: 1.8.5 (Windows 7), Board: "Arduino/Genuino Micro"
Sketch uses 4704 bytes (16%) of program storage space. Maximum is 28672 bytes.
Global variables use 313 bytes (12%) of dynamic memory, leaving 2247 bytes for local variables. Maximum is 2560 bytes.
An error occurred while uploading the sketch
An error occurred while uploading the sketch
Exception in thread "Thread-39" java.util.ConcurrentModificationException
at java.util.LinkedList$LLSpliterator.forEachRemaining(LinkedList.java:1239)
at java.util.stream.AbstractPipeline.copyInto(AbstractPipeline.java:481)
at java.util.stream.AbstractPipeline.wrapAndCopyInto(AbstractPipeline.java:471)
at java.util.stream.ForEachOps$ForEachOp.evaluateSequential(ForEachOps.java:151)
at java.util.stream.ForEachOps$ForEachOp$OfRef.evaluateSequential(ForEachOps.java:174)
at java.util.stream.AbstractPipeline.evaluate(AbstractPipeline.java:234)
at java.util.stream.ReferencePipeline.forEach(ReferencePipeline.java:418)
at cc.arduino.contributions.libraries.LibrariesIndexer.rescanLibraries(LibrariesIndexer.java:127)
at cc.arduino.contributions.libraries.LibrariesIndexer.setLibrariesFolders(LibrariesIndexer.java:106)
at processing.app.BaseNoGui.onBoardOrPortChange(BaseNoGui.java:682)
at processing.app.Base.onBoardOrPortChange(Base.java:1313)
at processing.app.Editor$DefaultExportAppHandler.run(Editor.java:2296)
at java.lang.Thread.run(Thread.java:748)
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
I'm wondering how can I know my board can work well or How I can I successfully upload the firmware.
Really, really, thank you.
Anyway,I followed the instruction on Wiki and now I'm using the "Update firmware" in gimx-launcher , but it always pops up "failed to load firmware". As I thought it would be problems in connection or something, I downloaded the Arduino Builder and tested my board.
(I think my jumpers and pins are a little loose, cause when I'm holding the intersections with a angle, a green light on the board would turn on.)
I used "serial monitor" it didn't work, no response.
Then I tried upload sketch, no error message. But when I tried to use "Upload using programmer" the error message came out.
Arduino: 1.8.5 (Windows 7), Board: "Arduino/Genuino Micro"
Sketch uses 4704 bytes (16%) of program storage space. Maximum is 28672 bytes.
Global variables use 313 bytes (12%) of dynamic memory, leaving 2247 bytes for local variables. Maximum is 2560 bytes.
An error occurred while uploading the sketch
An error occurred while uploading the sketch
Exception in thread "Thread-39" java.util.ConcurrentModificationException
at java.util.LinkedList$LLSpliterator.forEachRemaining(LinkedList.java:1239)
at java.util.stream.AbstractPipeline.copyInto(AbstractPipeline.java:481)
at java.util.stream.AbstractPipeline.wrapAndCopyInto(AbstractPipeline.java:471)
at java.util.stream.ForEachOps$ForEachOp.evaluateSequential(ForEachOps.java:151)
at java.util.stream.ForEachOps$ForEachOp$OfRef.evaluateSequential(ForEachOps.java:174)
at java.util.stream.AbstractPipeline.evaluate(AbstractPipeline.java:234)
at java.util.stream.ReferencePipeline.forEach(ReferencePipeline.java:418)
at cc.arduino.contributions.libraries.LibrariesIndexer.rescanLibraries(LibrariesIndexer.java:127)
at cc.arduino.contributions.libraries.LibrariesIndexer.setLibrariesFolders(LibrariesIndexer.java:106)
at processing.app.BaseNoGui.onBoardOrPortChange(BaseNoGui.java:682)
at processing.app.Base.onBoardOrPortChange(Base.java:1313)
at processing.app.Editor$DefaultExportAppHandler.run(Editor.java:2296)
at java.lang.Thread.run(Thread.java:748)
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
I'm wondering how can I know my board can work well or How I can I successfully upload the firmware.
Really, really, thank you.