Well i just installed everything yesterday,im using black ops for the emulator
i can get the mouse to move fast during aiming down sights, but everything just isnt fast enough
the one thing i cant figure out now, man i really edited this post alot
i been on here for for a couple hours
finally i just got one issue
i cant turn around fast, i have the ingame sensitivity set to max the x axis works wonderfully
wat exactly should i change in order to speed up my turning, i want to be able to turn around faster,
Please reply
thanks
trouble calibrating mouse
Re: trouble calibrating mouse
You have to increase the sensitivity (x multiplier) using the calibration mode:
1- tick the Mouse>Calibrate checkbox in sixemugui, and start emuclient
2- use rctrl+F1 to select the mouse
3- rctrl+F2 to select the config (config 2 is for aiming down the sights)
4- rctrl+F3 to modify the x multiplier
5- save (rctrl+F1) and quit the calibration mode (esc)
6- untick the Mouse>Calibrate checkbox, and test your new parameters
Repeat these steps until you get what you want. It's recommended to leave the calibration mode to test the parameters because there is some lag issue with it.
For the other parameters, you should try the normalized parameters:
1- tick the Mouse>Calibrate checkbox in sixemugui, and start emuclient
2- use rctrl+F1 to select the mouse
3- rctrl+F2 to select the config (config 2 is for aiming down the sights)
4- rctrl+F3 to modify the x multiplier
5- save (rctrl+F1) and quit the calibration mode (esc)
6- untick the Mouse>Calibrate checkbox, and test your new parameters
Repeat these steps until you get what you want. It's recommended to leave the calibration mode to test the parameters because there is some lag issue with it.
For the other parameters, you should try the normalized parameters:
Matlo wrote:
- Call Of Duty: Black Ops
- Primary config:
- dead zone 22, shape circle
- x/y ratio 2.85
- exponent 0.39
- Secondary config - ADS:
- dead zone 22, shape circle
- x/y ratio 1.71
- exponent 0.25
GIMX creator
- fourtysven
- Posts: 16
- Joined: Thu Aug 25, 2011 12:28 am
Re: trouble calibrating mouse
yeah i can turn much better now thanks man
i adjusted exponents and the x,y ratio, i have the numbers quite high
my xy multiplier is 7.00
and my x multiplier is at 8.30
The only thing i cant fix now is the mouse moving smoother
its still pretty fast but if i lower it i cant aim as quickly as i want
is this wat is supposed to happen with higher multipliers?
sometimes wen i aim fast towards a direction it almost looks like it skips, theres no one line motion
its a bit blocky and jittery
wat should i change?
thanks for reply
cheers
i adjusted exponents and the x,y ratio, i have the numbers quite high
my xy multiplier is 7.00
and my x multiplier is at 8.30
The only thing i cant fix now is the mouse moving smoother
its still pretty fast but if i lower it i cant aim as quickly as i want
is this wat is supposed to happen with higher multipliers?
sometimes wen i aim fast towards a direction it almost looks like it skips, theres no one line motion
its a bit blocky and jittery
wat should i change?
thanks for reply
cheers
Re: trouble calibrating mouse
Sorry there're a few things I don't understand. What's the "xy multiplier"? What's the "mouse moving smoother"?
As I told you, you have to save and quit the calibration mode to test new parameters, because the calibration mode is broken (it generates crappy movement).
As I told you, you have to save and quit the calibration mode to test new parameters, because the calibration mode is broken (it generates crappy movement).
GIMX creator
- fourtysven
- Posts: 16
- Joined: Thu Aug 25, 2011 12:28 am
Re: trouble calibrating mouse
i have high multiplier for x(9) under the calibrate mode,
wat helped speed it up was increasing the exponent from .39 to 80
I tried exited calibration mode and entered grab, basically
wen i move the cursor just a slight bit, it still isnt smooth, it looks smooth with faster aiming
but wen i break it down to very slow aiming, i can see there is small gaps, this would make it harder for far shots, im not sure if im explaining this well enough, if anything i will post a video showing the difference
wat helped speed it up was increasing the exponent from .39 to 80
I tried exited calibration mode and entered grab, basically
wen i move the cursor just a slight bit, it still isnt smooth, it looks smooth with faster aiming
but wen i break it down to very slow aiming, i can see there is small gaps, this would make it harder for far shots, im not sure if im explaining this well enough, if anything i will post a video showing the difference
Re: trouble calibrating mouse
I cured slow aiming jitters by upping the deadzone a little bit. Standardized is 22, but I have mine around 30.
My Config Repository | PSN: McKack - Steam: McKack - XBL: Ozukaki | Config Post Template
- fourtysven
- Posts: 16
- Joined: Thu Aug 25, 2011 12:28 am
Re: trouble calibrating mouse
it helped a bit, thanks mckack
i think its my mouse
wat do think of these settings. 2nd one is for aiming down sights
http://oi55.tinypic.com/2h5prtg.jpg
http://oi52.tinypic.com/ddkxtk.jpg
i think its my mouse
wat do think of these settings. 2nd one is for aiming down sights
http://oi55.tinypic.com/2h5prtg.jpg
http://oi52.tinypic.com/ddkxtk.jpg
Re: trouble calibrating mouse
I wouldn't have used exponents that high. I'd stick with the 0.39'er for CoD, both regular and aiming down sight, then used a higher multiplier instead.
My Config Repository | PSN: McKack - Steam: McKack - XBL: Ozukaki | Config Post Template
- fourtysven
- Posts: 16
- Joined: Thu Aug 25, 2011 12:28 am
Re: trouble calibrating mouse
k i found the mouse model its
GM278AA#ABA
http://www.epinions.com/specs/Hewlett_P ... se_GM278AA
this site says its 400 dpi
if i get a higher dpi mouse maybe that will soothe out the aiming?
or do i just need to increase the multiplier?
GM278AA#ABA
http://www.epinions.com/specs/Hewlett_P ... se_GM278AA
this site says its 400 dpi
if i get a higher dpi mouse maybe that will soothe out the aiming?
or do i just need to increase the multiplier?
Last edited by fourtysven on Sat Aug 27, 2011 5:57 pm, edited 3 times in total.