Mouse jitter

Need help? Ask here and someone will help
User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Mon Apr 10, 2017 12:01 pm

Changed it to 12.000dpi but it switched automaticly
back to 1.200dpi.
Will try it again and let you know if that will solve it.

Edit:
Changed it manually to 12.000dpi
Did nothing else with the config file. Didnt notice
any diffrence. Even with/without configuration it again.
The jumpy/jittery aim is still present.
My mouse is always on 12.000dpi when i start GIMX

User avatar
Matlo
Posts: 4239
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: Mouse jitter

Post by Matlo » Mon Apr 10, 2017 12:55 pm

Editing the config with gimx-config or gomx-fpsconfig causes the issue.
Change the value with a text editor after each time you save the config with gimx-config or gimx-fpsconfig.

I'll fix this issue in the next release (6.6).
Donate Shop

User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Mon Apr 10, 2017 1:00 pm

Changed it with a text editor.
It shows 12.000dpi now when i open the config file again.
But that didnt solve the issue

User avatar
Matlo
Posts: 4239
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: Mouse jitter

Post by Matlo » Mon Apr 10, 2017 1:15 pm

Did you perform the calibration again? Maybe the dead zone value is too high?
Donate Shop

User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Mon Apr 10, 2017 2:00 pm

Did the calibration process again.
Still jittery mouse movements. Dont know what it
could be. Its not a config calibration thing i think.
Even with a new or perfect calibrated file it starts to jitter.

The only time i see barely no jitter is when i switch from
“aiming“ mode to “driving“.
But that doesent solve my problem.

The UART converter can run with 3v or 5v TTL
Tried both. Seems to make no difference.

User avatar
Matlo
Posts: 4239
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: Mouse jitter

Post by Matlo » Tue Apr 11, 2017 8:07 am

Did you try to lower the dead zone?
Donate Shop

User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Tue Apr 11, 2017 12:10 pm

Yes i tried to lower it.
Low/high deadzone
Low/high sensetivity
Its always the same. As soon as i touch the mouse it starts to jitter.

User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Tue Apr 11, 2017 12:10 pm

Yes i tried to lower it.
Low/high deadzone
Low/high sensetivity
Its always the same. As soon as i touch the mouse it starts to jitter.

User avatar
Matlo
Posts: 4239
Joined: Wed Jul 06, 2011 7:01 am
Location: France
Contact:

Re: Mouse jitter

Post by Matlo » Tue Apr 11, 2017 12:56 pm

Did you check if there is the same behavior on a PC or a laptop?
This may tell if the issue is specific to the RPi3.
Donate Shop

User5001
Posts: 14
Joined: Sun Apr 09, 2017 11:34 pm

Re: Mouse jitter

Post by User5001 » Tue Apr 11, 2017 1:42 pm

Yes, its the same with my laptop.
Only thing i could test is to hook up the Arduiano directly
to the raspberry pi but i dont have the resistors.
I think the UART converter could cause the problem.

Did you check the link i posted?!
You can see the UART converter i use.

Post Reply