Hi.
I have an Arduino Micro loaded with atmega32u4.hex connected to the GPIO of a Raspberry Pi3. GIMX 5.9 has been installed on the Pi3, DS4 connected to the PI3 as well as the Logitech G27.
When trying to start GIMX I get the following error: adapter_detect failed
I have swapped RX and TX to make sure that this is not the problem.
Please can someone assist.
Arduino Micro + Raspberry Pi3 + PS4
Re: Arduino Micro + Raspberry Pi3 + PS4
Image of setup
[img]
https://www.dropbox.com/s/c97oe2kn2dyb9 ... 3.jpg?dl=0
[/img]
Image of Log
[img]
https://www.dropbox.com/s/gu7ioz6txe8fc ... 4.jpg?dl=0
[/img]
[img]
https://www.dropbox.com/s/c97oe2kn2dyb9 ... 3.jpg?dl=0
[/img]
Image of Log
[img]
https://www.dropbox.com/s/gu7ioz6txe8fc ... 4.jpg?dl=0
[/img]
Re: Arduino Micro + Raspberry Pi3 + PS4
Hi Matlo
How many watts should the resistors be?
Regards,
Paul
How many watts should the resistors be?
Regards,
Paul
Re: Arduino Micro + Raspberry Pi3 + PS4
I added the resistors but am still getting the same error as posted previously.
[img]
https://www.dropbox.com/s/y1gnar0usyu1q ... 8.jpg?dl=0
[/img]
[img]
https://www.dropbox.com/s/y1gnar0usyu1q ... 8.jpg?dl=0
[/img]
Re: Arduino Micro + Raspberry Pi3 + PS4
Did you through the "Software adjustments" part of the wiki?
Did you turn the PS4 on before starting GIMX?
Did you turn the PS4 on before starting GIMX?
GIMX creator
Re: Arduino Micro + Raspberry Pi3 + PS4
Hi Matlo
I'm using the PS4 to power the PI so its on before i try and start GIMX.
is that the correct order?
I'm using the PS4 to power the PI so its on before i try and start GIMX.
is that the correct order?
Re: Arduino Micro + Raspberry Pi3 + PS4
Hi Matlo
I have managed to get a Teensy 2++ controller. I have followed this tutorial
http://www.psx-place.com/threads/tutori ... g-pi.9744/
But get the same error as when I used the Arduino. What am i doing wrong? Why does GIMX not startup?
Regards, Paul
I have managed to get a Teensy 2++ controller. I have followed this tutorial
http://www.psx-place.com/threads/tutori ... g-pi.9744/
But get the same error as when I used the Arduino. What am i doing wrong? Why does GIMX not startup?
Regards, Paul
Re: Arduino Micro + Raspberry Pi3 + PS4
Please see the log below.
global option -l with value `log.txt'
global option -c with value `LogitechG27_G29.xml'
controller #1: option -p with value `/dev/ttyAMA0'
now reading arguments for controller #2
grab flag is unset
status flag is set
subpos flag is set
force_updates flag is set
GIMX 5.9 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.1.21-v7+ #873 SMP Mon Apr 11 18:22:10 BST 2016 unknown
Bus 001 Device 006: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Blue$
Bus 001 Device 005: ID 046d:c294 Logitech, Inc. Driving Force
Bus 001 Device 004: ID 054c:05c4 Sony Corp.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast$
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Vendor Specific Class, Driver=smsc95xx, $
|__ Port 3: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 4: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 1, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 2, Class=Human Interface Device, Driver=usbhid, 1$
native mode command sent to HID device 01:01:04 (PID=c294)
native mode enabled for HID device 01:01:04 (PID=c29b)
serial_send
No controller detected.
adapter_detect failed
global option -l with value `log.txt'
global option -c with value `LogitechG27_G29.xml'
controller #1: option -p with value `/dev/ttyAMA0'
now reading arguments for controller #2
grab flag is unset
status flag is set
subpos flag is set
force_updates flag is set
GIMX 5.9 ARMv6
Raspbian GNU/Linux 8.0 (jessie)
Linux 4.1.21-v7+ #873 SMP Mon Apr 11 18:22:10 BST 2016 unknown
Bus 001 Device 006: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Blue$
Bus 001 Device 005: ID 046d:c294 Logitech, Inc. Driving Force
Bus 001 Device 004: ID 054c:05c4 Sony Corp.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast$
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
|__ Port 1: Dev 3, If 0, Class=Vendor Specific Class, Driver=smsc95xx, $
|__ Port 3: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 4: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 0, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 1, Class=Human Interface Device, Driver=usbhid, 1$
|__ Port 5: Dev 6, If 2, Class=Human Interface Device, Driver=usbhid, 1$
native mode command sent to HID device 01:01:04 (PID=c294)
native mode enabled for HID device 01:01:04 (PID=c29b)
serial_send
No controller detected.
adapter_detect failed