salut Matlo,
I'm trying to flash the payload for DS4 (firmwares\EMUPS4\atmega32u2.hex) on Minimus (ATmega32u2) and all seems well but after reset the minimus isn't recognized as 'Wireless Controller'. It actually isn't recognized at all, both leds are lit (red and green) and this doesn't happen if I write the EMUPS3 payload (only green led is lit).
if I use the same approach with 'firmwares\EMUPS3\atmega32u2.hex' all is well and the minimus is recognized as PS3 controller.
Do I need an ATmega32u4 instead of the ATmega32u2?
Anyway, I tried with it as is and it doesn't work.
When the PS4 boots up I get these error messages on the GIMX console:
[..]
unhandled packet (type=0x40)
unhandled packet (type=0x80)
unhandled packet (type=0xff)
unhandled packet (type=0x40)
unhandled packet (type=0x80)
unhandled packet (type=0xff)
unhandled packet (type=0x01)
unhandled packet (type=0x00)
unhandled packet (type=0x80)
unhandled packet (type=0x00)
unhandled packet (type=0xff)
unhandled packet (type=0x00)
unhandled packet (type=0x00)
unhandled packet (type=0x00)
unhandled packet (type=0x00)
unhandled packet (type=0xff)
unhandled packet (type=0xff)
unhandled packet (type=0x00)
unhandled packet (type=0x00)
unhandled packet (type=0xff)
unhandled packet (type=0x00)
unhandled packet (type=0x00)
unhandled packet (type=0x80)
unhandled packet (type=0x00)
unhandled packet (type=0x80)
Then if I stop the ps4 and start it again I get:
wLength (22560) is higher than 247
adapter_forward_data_out failed
wLength (22560) is higher than 247
adapter_forward_data_out failed
Button mapping seems fine as I get the buttons status in the GIMX console when I press them.
I use a DIY with CP2102 and the Minimus AVR http://www.ck3.co.uk/minimus-32-avr-atm ... board.html
I also use Windows 7 64bit and GIMX 3.4 x86_64 and I have replaced the driver to libusbK with Zadig.
Btw, it works very well on Ubuntu via Bluetooth, so again, thanks very much! Chapeu!
thanks in advance for your support!
cordialement
PS4 Problem on Windows 7
Re: PS4 Problem on Windows 7
Hi,
The PS4 has to be started before GIMX. And you should stop GIMX before the PS4.tps wrote:When the PS4 boots up I get these error messages on the GIMX console:
GIMX creator
Re: PS4 Problem on Windows 7
Tried that too. Is it normal that the payload/firmware for the Atmega isn't identified as Wireless Controller by Windows 7?
Also, the two leds ar both lit: RED+GREEN.
Merci!
Also, the two leds ar both lit: RED+GREEN.
Merci!
Re: PS4 Problem on Windows 7
with Ubuntu and some tweaking, I get this which is sweeet!
https://drive.google.com/file/d/0B9QsY5 ... ltazQ/view
merci!
https://drive.google.com/file/d/0B9QsY5 ... ltazQ/view
merci!
Re: PS4 Problem on Windows 7
Great What kind of controller are you using? A racing wheel?
For the Windows issue: did you install the CP2102 windows driver?
For the Windows issue: did you install the CP2102 windows driver?
The firmware does not initialize the USB interface until GIMX is started, and the adapter is reset when GIMX stops.tps wrote:Tried that too. Is it normal that the payload/firmware for the Atmega isn't identified as Wireless Controller by Windows 7?
GIMX creator