Search found 20 matches
- Sat Jan 05, 2019 5:43 pm
- Forum: Support
- Topic: Keyboard not responding
- Replies: 2
- Views: 2841
Keyboard not responding
Hello All I've been using GIMX for a while but this has got me puzzled. I am using the Shop purchased GIMX board with the firmware to power the DS4 controller. This has worked for me previously but I had to use the Raspberry Pi SD card for something else. Anyway, I have put a new card in with the sa...
- Tue Jun 27, 2017 9:55 pm
- Forum: General Discussion
- Topic: RP3 + DIY USB + DS4
- Replies: 5
- Views: 6364
Re: RP3 + DIY USB + DS4
I'm a real fan of your work, I have put a donation forward so I do hope it helps you in some way. I've done another video to show how I change my config. Not many people use linux but hopefully this will help. I am sure I could have used SCP to do this but I was having a 'Gav' moment so couldn't get...
- Tue Jun 27, 2017 9:50 pm
- Forum: Support
- Topic: Wrong firmware?
- Replies: 3
- Views: 3796
- Tue Jun 20, 2017 5:05 am
- Forum: Support
- Topic: GIMX adapter changing firmware Linux
- Replies: 7
- Views: 5808
Re: GIMX adapter changing firmware Linux
Cool. Thank you for your help on this its been very appreciated.
- Tue Jun 20, 2017 4:48 am
- Forum: General Discussion
- Topic: RP3 + DIY USB + DS4
- Replies: 5
- Views: 6364
Re: RPi3 + DIY USB + DS4
I have now got this up and working.
Matlo - a personal thank you for the hard work and effort you have put into this. I got the adapter and helped me get that up and running.
This is my setup
https://youtu.be/G8Lsa1NEPRs
Matlo - a personal thank you for the hard work and effort you have put into this. I got the adapter and helped me get that up and running.
This is my setup
https://youtu.be/G8Lsa1NEPRs
- Mon Jun 12, 2017 9:02 pm
- Forum: Support
- Topic: GIMX adapter changing firmware Linux
- Replies: 7
- Views: 5808
Re: GIMX adapter changing firmware Linux
Hello Matlo I am all sorted now. I managed to run the sequence as you suggested. To help others. 1. Plug in both the USB and USB cables 2. Remove the USB cable 3. Plug USB cable back in 4. Use the command 'chmod 777 /dev/ttyAMC0 5. Remove the USB cable again 6. Plug the USB cable back in again 7. Ru...
- Mon Jun 12, 2017 8:01 pm
- Forum: Support
- Topic: GIMX adapter changing firmware Linux
- Replies: 7
- Views: 5808
Re: GIMX adapter changing firmware Linux
Sorry Matlo, I realised I didn't explain what I was doing. I am trying to load the firmware on to the GIMX adapter initially. The file I need to load is atmega32u4.hex for a standard PS4 controller (under folder EMUPS4). Unless the EMUG29PS4 hex file supports the PS4 controller in which I am wasting...
- Mon Jun 12, 2017 7:36 pm
- Forum: Support
- Topic: GIMX adapter changing firmware Linux
- Replies: 7
- Views: 5808
Re: GIMX adapter changing firmware Linux
Thanks Matlo Well I have moved forward but stuck I am getting an error which seems to be generic. avrdude: ser_open(): can't open device "/dev/ttyACM0": No such file or directory From the digging around I have done it is almost as if it is not being detected hence why I am not seeing /dev/...
- Sun Jun 11, 2017 5:30 am
- Forum: Support
- Topic: GIMX adapter changing firmware Linux
- Replies: 7
- Views: 5808
GIMX adapter changing firmware Linux
Hello So I purchased the official adapter but I am struggling with changing the firmware. I am sure this is going to be a very simple thing but here is where I am stuck. The adapter based on the atmega32u4 chip but when I look at the loaders available I see that it seems the linux varients state &qu...
- Thu May 11, 2017 9:21 pm
- Forum: General Discussion
- Topic: RP3 + DIY USB + DS4
- Replies: 5
- Views: 6364
RP3 + DIY USB + DS4
Hello Guys Well its been a good time while it lasted but my old trusty laptop took a direct hit and died. So I am therefore resurecting getting the RP3 up and running. Before hand I had been using the bluetooth way but I am going to try the DIY USB adapter. Now my question is a basic one but one tha...